14052: Iron Rock Off Road ZJ 3.5" ROCK-LINK Long Arm Lift Kit

0 Review(s) Write a Review

Your Price: $2,251.24

Part Number: IRO-14052

Shock Options *

Upgrade to IRO Sway Bar Disconnects *

Quantity

Description

The paramount suspension upgrade for your ZJ is a long arm system. Iron Rock Off Road's 3.5" ROCK-LINK link long arm system offers unrivaled performance, giving your Jeep both the capability and ride quality improvements that you have been looking for. This ROCK-LINK long arm lift kit is built for strength, clearance, adjustability, flexibility, and ease of install.

STRENGTH: Our subframe is constructed with 1/4" steel and our lower arms are even thicker at 2"x5/16" wall D.O.M. tubing.
CLEARANCE: We tuck our subframe up as tight as possible to gain you the critical extra clearance to keep your Jeep low and your belly high! The lower arm connections at the chassis are as high as possible with still being able to install a bolt through them. The control arms have an inboard bend to clear your tires, so you can steer lock to lock without rubbing on them
ADJUSTABILITY: All the arms have tons of adjustment built in for your stock situation to your stretched crawler.
FLEXIBILITY:Yes, of course we are talking about articulation, and the ROCK-LINK delivers plenty! But we are also talking about flexibility to install other axle combinations with ease. Use this kit with your stock Dana 30 for now, and then bolt in a Dana 44 or Dana 60 down the road!
EASE OF INSTALL: No welding, no complicated setup or templates. All you need is a drill, a floor jack, some jack stands and some hand tools. This is a BOLT-IN kit, although if your preferred method of installation is welding, you can do that! (NOTE: Required cut off the factory lower control arm mounts on the chassis)

KEY PRODUCT FEATURES:

5/16" thick wall D.O.M. lower control arm material
1/4" thick, 3 piece, subframe assembly
Huge tire clearance with inboard control arm bends
Best ground clearance available with super high clearance long arm subframe mounts
Makes axle swaps much simpler!
Maintains caster through the suspension cycle
Easy to install without welding, only simple drilling is required!!! Seriously, you can install this in your driveway in a few hours!

INSTALLATION NOTES:

This kit is 100% bolt on!! Strength is not compromised with this value added design feature. However, for those of you still concerned about strength, you can weld the subframe inor bolt AND weld them in (welding to the uniframe is complicated and should be done by an experienced professional welder). The choice is yours.
The front subframe is assembled from 3 pieces. This will allow you to remove the center section for transmission/t-case access while leaving the front suspension (long arms) installed.
If your ZJ has the CV (with rubber boots) front driveshaft, you may need to convert to the double cardan style to accommodate the lift height. Your rear driveshaft will work with this kit.
We do offer a heavy duty SYE for the 231 transfer case and a hack-n-tap SYE for the 231 and 242. Using a slip yoke eliminator has been proven to reduce and/or eliminate vibrations that may occur with taller lifts.

NOTE: This kit has not been tested with aftermarket headers and is known not to work with Doug Thorley Headers without modification.

KIT INCLUDES:

Front and rear coil springs
Front high clearance subframe assembly
Front 3 Link Long Arm Kit
Heavy Duty Adjustable rear upper and lower control arms.
Heavy Duty Double shear track bar conversion (front)
Heavy Duty Rear adjustable track bar
Front and rear shock absorbers
Heavy duty extended front sway bar links
Rear extended length sway bar links
Extended length stainless steel brake hoses
All necessary hardware

INSTRUCTIONS:

Detailed Installation Instructions

REV-JK-RUB-513: Revolution Gear Package (Timken Bearings), Jeep Wrangler JK Rubicon, 5.13 Ratio

$743.99

(0)

Add to Wish List

Add To Cart

D44RS-538RUB: Revolution Gear & Axle Dana 44 Jeep JK Front Ring & Pinion, 5.38 Ratio

$221.99

(0)

Add to Wish List

Add To Cart

D60-538R: Revolution Gear & Axle Dana 60 Reverse Ring & Pinion, 5.38 Ratio

$251.99

(0)

Add to Wish List

Add To Cart

YGK018: Yukon Gear & Install Kit Package, Standard Rotation Dana 60 Front/’88 & Down GM 14T Rear, 4.56 Ratio

~~$1,299.89 Original price~~ $1,194.00 Sale

(0)

Add to Wish List

Add To Cart

14052: Iron Rock Off Road ZJ 3.5" ROCK-LINK Long Arm Lift Kit

Choose Options

Related Items

Recently Viewed Items

Mailing List